กก
(a) room choice (pre)
In the choice of room, try to choose not to and other people's
room only a wall of the room, this will increase the difficulty
of the whole renovation, and the effect is greatly decreased.
Plane conditions permitting, the best choice of the room (wall,
ceiling, floor and others) to separate, for example, facing the
street or other room near his house, this can reduce the impact
on other people's. Then, it is best to select the shape of the
rectangular room for comparison, so the construction of the
difficulty is not so big, after the completion of their sound
field effect will be more comfortable.
(two) the choice of sound insulation materials (early stage)
Insulation material and sound-absorbing material selection is
also very important. Be clear about some of the material you
choose, it's what it is, if there is only a very vague concept,
the effect is certainly not up to your expectations.
I listed my choice of materials for reference. This name is used
by my side of the market of the material's name may not be very
accurate, but I will try to describe them, they will use their
specific instructions in this article, some materials may not
see, will also specify the. Because I'm not very professional,
so when the sound-absorbing material is not very good according
to what kind of material absorption which the frequency of the
sound the best choice, but according to the frequency range of
about, is simply divided into low frequency, intermediate
frequency and high frequency.
Groove wood, balk, gypsum board, sound insulation mat, polyester
fiber sound-absorbing cotton, wave absorbing sponge carpet.
These are the main material, and there are some nails, wave
sponge special glue what ah, is not tired syria. This inside, if
you are not entirely their own hands, but the renovation team to
do so, then some of them can not buy their own materials, and
the decoration team speak clearly. But the general contractor
may be a little more expensive than materials and their
preparation, to spend money to buy it convenient.
(three) to make the noise of the room to do the early
construction of basic facilities (noise)
Early here that the civil infrastructure refers to make your
room more suitable for sound insulation decoration, it including
a few items, you can according to their actual situation of the
reference room:
1, all the original window where all abandoned, with a brick
cement seal; because I was on the first floor, there is a
balcony outside the door, in order to better sound insulation I
put the balcony is bricked up, leaving out a door;
2, my room because there is a wall and is adjacent to the
others, so I pay special attention to the distance it is about a
brick wide position and I built a wall, which is equal to the
home and others have two walls separated, and the middle there
is a brick wide gap, which can play to better sound effects.
Another point: because the room is relatively sealed, if you
want to be comfortable in the future if you want to install air
conditioning. At this time will be expected to be good in the
future air conditioning location, pre drilling air conditioning
condensate pipe and drainage pipe holes, or when the time of the
village to drill on the trouble. Do not buy the kind of old air
conditioner in order to save money to buy air-conditioning, so
that the opening is too large, very detrimental to the sound.
Now split type air conditioning is not expensive, and do not
save that money in the future will regret it later. The same
room, after what places to Zhuang power supply, lighting, wire
to distribution, all these at this time will be planned at each
step below, remember to set aside these facilities.
In short, the whole sound insulation decoration is basically an
irreversible process, as far as possible to do the preparatory
work in the early pre do, so you can reduce rework rate. Of
course, there will certainly be a shortage of places, I was
going through a lot of different situations, and every time I
have to think of ways to remedy, so that they are in trouble.
(four) to the whole room nail long skeleton (noise)
The first is sticking damping soundproof felt in the original
wall, then making a keel frame, is to use wooden nail into the
shelf, and a grid of horizontal and vertical, the common
procedure of general decoration. Is the selection of groove
wood, wood is a wood for mean.
If the type is 2 meters long; groove refers to the wood on every
certain length of pre made a bayonet, such as wood thickness is
6 cm, in the opening position on the remaining 3 cm thick, so
that when every two wooden cross,
The intersection position is right back to mount each other
together 6 cm thick. That seems to be very troublesome in fact
the country's timber market should be unified, if you buy it in
a place to buy wood to see it, the decoration team also
understand. that
Yao long skeleton assembly nail up after it should be like this:
The area of the keel frame is determined according to the area
of each wall, and the area of the wall is equal to the area of
the wall. Of course, here to calculate good, every two phase of
the wall, the area of the keel frame is not equal to the wall,
and one of the wall corresponding to the length of the keel
Must be minus the thickness of a piece of wood, because your
other wall has been nailed to the Dragon skeleton, and will
occupy a wooden side of the thickness of it.
The next is to fix on the wall. There is a place to pay
attention, can not be directly to the Dragon skeleton wall nail,
must first go to the wall above a number of nail root support
piles, and then the Dragon skeleton nails in the supporting
pile. A lot of friends is done after the Dragon skeleton
straight
Then nailed to the wall, so that the effect of a lot of
difference. Support pile is used in the previously mentioned
balk, balk hardness is relatively large, relatively thick, used
as a support will be relatively stable, there is no groove of
the balk. Attention screw support pile
The position of the pile in the wall can be pre well supported,
so that the screw can be smoothly nailed to the supporting pile
in order to nail the keel frame.
The use of support pile has two advantages, the first is to make
the wall surface and the keel frame spaced a certain space, let
the sound abatement in surface penetration of different media,
play a sound effect; second reduction in direct contact with the
Dragon skeleton and the wall surface, in the
When the vibration is generated, it can reduce the vibration
spread to the wall. The disadvantage is that the available area
of your room is small, because this will definitely be the area
of your room to narrow the. Similarly, the ceiling is the same
(to 90 degrees).
The impact on the upper floor may be greater, so it is better to
support the pile can be longer than the wall, of course, for the
ceiling is not a supporting pile but a pile up. My setting is,
the wall of the supporting pile 15cm, hanging on the ceiling of
the ceiling
25cm. The length of the supporting pile is the longer the sound
insulation effect is better, we can according to their actual
situation to arrange. After it is installed:
Above the ceiling hanging pile do not have to use wood, can use
steel, expansion screws and so on, the decoration will help you
take the key to stable. In the construction of the best is the
first part of the ceiling to do a good job, and then started to
do the wall of the Dragon
Skeleton. Because hanging ceiling, the height of the wall is
low, the area is also reduced, then the use of the material is
less. And the ceiling of the construction is the most difficult,
in other parts of the construction before doing a good job is
relatively good.
The number of supporting pile depends on the size of the walls,
a dense of dragon skeleton would be more stable, but not too
close, next time put polyester fiber sound-absorbing cotton will
be more trouble, but also multi process. Generally the best key
Place a few roots, the dragon can support the stability of the
skeleton on the line. Remember to say in front of the well
prepared to put power, cloth wire position, this time will be a
good wire to the direction of the. Of course, you can also
choose to use the wire slot to allow
Wire in the appearance of the bright go, then wait until the
sixth step is completed after the wire can also be. (the power
supply does not need to prepare too much, in addition to the
general lighting outside the wall or a maximum of every one on
the line, when the time comes with the regulator or the
On the line, extending the expansion board)
(five) the polyester fiber sound-absorbing cotton placed between
the frame and the wall of the Dragon (sound)
Polyester fiber sound-absorbing cotton, is a special material
sound-absorbing material, is the kind of pure white, it is not
difficult to handle, is what we usually see the clothing label
contains how many percent of polyester fiber, when buying is a.
The specific specification is wide 60
Cm, 1.2 meters long, remember my 14 square meters of the room,
bought 63 just good, we can measure the total area of the wall
and ceiling and then buy. Polyester fiber sound-absorbing cotton
is the main absorption of high frequency sound, put the time to
make it as far as possible
Loose, enlarged contact surface with sound. Do not thick a large
group on the inside plug, also do not fold into a few contacts
between the inside, these are not conducive to the sound
absorption. If you think there is a need, you can put a layer of
another layer of (I only put one
Layer). Some friends are accustomed to the use of a quilt, that
the quilt is relatively easy to buy, the price is relatively
cheap. But in fact the first cotton fiber sound-absorbing
ability is not strong sound-absorbing cotton, then the quilt
density is too high too much, is not conducive to the sound and
everyone in this
Say to choose polyester fiber sound-absorbing cotton recommended
density per cubic 30-35kg (and buy so many quilts are not
necessarily cheap, unless through special channels, such as when
I was faced with college graduates, many graduates do not
collect
The quilt). If you really want to use the quilt, it is best not
to mind taking the trouble will quilt up, let the internal
structure becomes loose, and then spread evenly placed.
Cotton insulation fixed as long as the top edge or corner with a
small nail, the nail in the wood above what pushpin, then let it
down on the line. This involves a step that support pile number,
if it is too thick, will affect the sound absorption
Cotton placed, can only be cut into small pieces, and the
trouble is not good, so the density of the support pile should
be properly allocated according to the actual situation.
Sound-absorbing cotton place after about is this:
Undefined
Still have the habit of friends with glass cotton this reminder
to millions of millions of attention! Glass wool powder is
harmful to the human body! Place the time must be to avoid
contact with the powder on the skin, especially more as far as
possible not to inhale and enter the eyes of the respiratory
tract, not
But it will be very uncomfortable. When placed to wear long
sleeved clothes, wearing masks, working gloves, the best
conditions to wear goggles. If they are exposed to the skin,
wash with soap and water as soon as possible; if you
accidentally enter the eyes, rinse with water, the
Eye drops of eye drops; accidentally sucked in...... I do not
know how to do, anyway, general serious send hospital. -__-|#
And, after the completion of the glass wool, as soon as possible
to complete the following procedures to say, to avoid the long
time exposure of glass wool in the air.
Finally, the sentence, remember to give you the power to set
aside. Select the wires and the next friend can wait for the
next step to consider the issue of wire.
(six) the installation of gypsum board on the surface of the
keel frame (sound)
The gypsum board so that the energy consumption so as to achieve
the effect of sound absorption. Some friends are accustomed to
using thin wood, but in fact, this is not good. Because here is
to use the principle and the principle is not sound insulation.
The board does not have the ability of absorbing many
, and if you want to use the wood to noise, then the effect is
very poor. Micro punching board does not have to use a gypsum
board, can also be used as a hard plastic or PVC, metal plates,
etc., but relatively speaking, the price of gypsum board is
relatively cheap, and it is
The main surface of the wall is relatively strong, people rely
on. Nothing (as long as you don't idle wall play ^_^). When
installed on the board in advance as long as several screw
holes, and then use self tapping screws to tighten the wooden
dragon skeleton line.
install
This step is done later, if you intend to go to the wire before
the start of the wiring. Wire with a wire slot, lead to the
place where you want to install power supply, power supply,
ok~~~! Also remember, you have to install air conditioning, put
you ready to put split
The indoor air conditioning that part of the local blank, do not
seal the gypsum board
(seven) on the surface of gypsum board on the wave absorbing
cotton (sound)
The wave crest cotton also called sound-absorbing cotton (cotton
egg) is actually a sponge, is generally a large black. One side
of it is flat, used to stick on other surfaces, and the other
side is undulating waves.
Undefined
Wave cotton
Undefined
Wave cotton is the absorption of intermediate frequency, high
frequency range of sound. And the most important, it can make
the surface of the wave shape of the sound inside the room to
reduce the specular reflection, resulting in diffuse reflection,
so that the room is not a straight line of sound back and forth,
ear
It sounds very comfortable. It's an indispensable item in the
recording room and rehearsal room. Wave cotton according to the
thickness of different prices are not the same, the more the
more expensive the more expensive the effect is better, it is
best to buy a thick bar. Some friends in order to save money in
the food market to buy that kind of
Egg shell, although it is also a wavy surface, but because it's
not as good as the internal structure of porous sponge, the
hardness is too high, so there is no sound-absorbing effect what
basically, and it is not the surface wave cotton can cause
diffuse back
The effect of the shot is strong, so it is not recommended to
use.
Sticky wave cotton when the need to use its special glue, in the
place where there is a wave of cotton, glue also has the use of.
This kind of glue stick up after still relatively strong, as
long as it is not smooth surface on the line. The surface of the
micro perforated plate is opened.
Countless holes, it's a rough surface.
This process is relatively simple, to stick on the line, not on
the chart. You have the power, you have the power of the place,
the wave of cotton cut open in order to protect the power supply
will not be covered.
(eight) floor and door (noise)
Here to the floor and the door get out say, because if the two
part did not deal with it, the front of the process may be equal
to a waste.
Floor: the floor of the noise reduction in addition to wall and
ceiling of the same process, there is also a need to pay
attention to the principle, is to reduce vibration (not
vibration). Because our drum or sound box produces vibration,
can be directly and the floor
Contact, so it will directly cause the floor vibration. If you
are like me in the first floor of the shop, a relatively thick
carpet on the floor, but if you have people living downstairs,
then you have to be on the floor of the drum, speakers "soft
touch
Treatment. There are many ways to do the first dragon skeleton
such as walls and ceilings (like on the surface of the keel
frame here do not use gypsum board, covered with thick wood
because people have to walk on it.), on top of the plank can be
used across the floor
Cushion, cushion, cushion, cushion and so on, to achieve the
effect of "soft touch". Undefined
Door: the door is also a very very important factor, many of the
rehearsal room is because the processing of the door did not do
a good job and was a complaint. Door handle is a principle -
sealed!! Here are two elements: 1, the door of the side. Can be
used with thick velvet
Cloth wrapped edge, the closing time can be as tight as possible
without the door. 2, if there are conditions, it is best to make
a continuous door two to open to both sides, in the middle of a
certain space. This can be made into the gap layer of sound
insulation, and can be very good
The repair of the single door seal is not good enough. It seems
that there is a kind of prefabricated door is this structure, in
the middle of a vacuum, the effect is even better.
.